太阳集团城娱8722-主頁|欢迎您!

首页 > 产品中心 > RETZ瑞茨阀门 > 球阀系列 > 氨用球阀 氨气 氟利昂专用球阀

氨用球阀 氨气 氟利昂专用球阀

简要描述:RETZ进口氨用球阀,氨气,氟利昂专用球阀广泛应用在石油、化工、制药、化肥、冷冻等工业部门的自动化控制系统中,可分别适用氟利昂、气体、氨气、液氨、氨水等腐蚀性与非腐蚀性介质

  • 品牌:RETZ
  • 工况条件:开 关
  • 温度/压力:P-T: 40bar@120℃
  • 更新时间:2022/10/26
产品详情 在线咨询

进口氨用球阀,氨气,氟利昂专用球阀性能描述 Performance description进口氨用球阀2.jpg

氨用球阀球阀(氨气,氟利昂专用球阀)全通径设计,浮动球芯结构,具有最大的流通能力。碳钢阀体表面均经黑色磷化处理,具有抗腐蚀、防止生锈的作用 RETZ Full bore design of ammonia ball valve (ammonia, Freon special ball valve), floating core structure, with maximum flow capacity. The surface of carbon steel valve body is treated with black phosphating, which has the function of corrosion resistance and rust prevention


执行标准 Executive standards

设计标准 Design Rating∶ASME B 16.34

结构长度Face to Face∶ASME B16.10

法兰标准Flanged Ends∶ASME B16.5

检查和试验 Inspection & Testing∶API 598

尺寸

1/2”~20”

压力等级

Class150~Class300

温度范围

软密封

-29~120℃

硬密封

-20~80℃

法兰标准

ASME B16.5

结构长度

ASME B16.10EN558

性能规范

ASME B16.34


进口氨用球阀,氨气,氟利昂专用球阀阀座材料 Valve seat material

聚四氟乙烯(PTFE

优点耐温(-196~120℃

耐腐耐强酸强碱、水和各种有机溶剂。无毒害/不粘附/高润滑/耐气候。机械性质较软,塑料王之称

巴氏合金

特点因其呈白色,又称白合金,低硬度轴转动的材料。

熔点固相点温度为240℃,液相点温度为370℃,仅限使用温度不得超过100℃摩擦系数在有油时为0.005,无油时为0.28

聚四氟乙烯(PTFE).jpg巴氏合金.jpg

阀杆结构 Stem structure

采用下装式阀杆防飞出倒密封结构,即阀杆是从阀体内部倒装,并在阀杆的尾部加工有锥面台阶,这样的设计当阀腔压力异常升高或在停机检修时,阀杆不会被冲出;这种结构同时可实现阀杆自密封,阀腔压力越高阀杆的密封性能就越好,而且这种倒密封结构可以有效的防止阀杆和阀体的阀杆结构.jpg摩擦,从而起到降低阀门操作扭矩的作用 retz品牌 The bottom mounted valve stem anti fly out sealing structure is adopted, that is, the valve stem is installed upside down from the inside of the valve body, and the taper step is machined at the end of the valve stem. In this design, when the pressure of the valve chamber rises abnormally or the valve stem is shut down for maintenance, the valve stem will not be flushed out; This structure can also realize the self sealing of the valve stem. The higher the valve chamber pressure, the better the sealing performance of the valve stem. Moreover, this reverse sealing structure can effectively prevent the friction between the valve stem and the valve body, thus reducing the valve operating torque

阀杆密封填料标准配置材料为PTFE,是由一组V型填料和填料垫组合而成,这样能有效的将填料压盖的预紧力转化为阀杆的密封力。防火型及硬密封阀门将采用柔性石墨作为填料和倒密封垫  The standard configuration material of the valve stem sealing packing is PTFE, which is composed of a group of V-shaped packing and packing pads. This can effectively convert the preload of the packing gland into the sealing force of the valve stem. Fireproof and hard seal valves will use flexible graphite as the packing and back sealing gasket


阀座结构 Valve seat structure

阀座采用弹性槽减压设计,在低压和高压下均能提供可靠地密封,并且具有自动泄压的功能,当阀腔压力异常升高时,阀腔介质能依靠本身的压力挤压弹性阀座而自动泄压,从而确保了阀门安全并且有效的降低了阀门的操作扭矩  The valve seat is designed with elastic groove 阀座结构.jpgdecompression, which can provide reliable sealing under low pressure and high pressure, and has the function of automatic pressure relief. When the pressure of the valve chamber rises abnormally, the medium in the valve chamber can automatically relieve the pressure by squeezing the elastic valve seat with its own pressure, thus ensuring the safety of the valve and effectively reducing the operating torque of the valve

所有阀座在径向方向均设有V型切口这样的设计,可防止软密封阀座材料因受热膨胀而导致阀门卡死不能动作  All valve seats are equipped with V-shaped notch in the radial direction, which can prevent the valve from being stuck and unable to act due to thermal expansion of soft sealing valve seat materials

标准阀座材料为PTFE(聚四氟乙烯);可供选择的阀座材料有RPTFE(增强型聚四氟乙烯),PEEK(聚醚醚铜)等。

 软密封结构.jpg

硬密封结构阀座材料为巴氏合金,根据用户要求或阀门使用温度的不同RETZ可提供0Cr18Ni9堆焊STL合金

硬密封结构.jpg

防火结构 Fireproof structure

带有防火结构设计。当发生火灾或其他因素导致阀门温度过高使软密封阀座受损时,球体会随着管道内介质压力的推动与阀体金属密封面接触形成第二级金属对金属密封,从而保证阀门在软密封阀座受损后仍然具有良好的密封性能;同样在阀门阀体和阀盖之间(中道)采用止口法兰、金属对防火结构.jpg金属二级密封设计,这样的设计可对阀座和中道垫片提供恒定的预紧力,防止阀座和中道垫片被无限压缩而失效,同时有效的降低了阀门因管道震动、扭转等其他外力因素对中道垫片造成的损坏,从而起到保护阀座和中道垫片,降低阀门操作扭矩,延长阀门使用寿命的作用  With fireproof structure design. When the soft seal valve seat is damaged due to the high temperature of the valve caused by fire or other factors, the ball will contact the metal sealing surface of the valve body to form a second level metal to metal seal with the push of the medium pressure in the pipeline, so as to ensure that the valve still has a good sealing performance after the soft seal valve seat is damaged; Also, the design of lip flange and metal to metal secondary seal is adopted between the valve body and bonnet (middle channel). This design can provide a constant preload on the valve seat and middle channel gasket, prevent the valve seat and middle channel gasket from being invalid due to infinite compression, and effectively reduce the damage to the middle channel gasket caused by other external forces such as pipeline vibration and torsion, thus protecting the valve seat and middle channel gasket, Function of reducing valve operating torque and prolonging valve service life


球芯结构 Ball core structure

球体均经磨床精密加工而成,表面采用镜面抛光技术,有效的保证了球体的圆度。根据客户的不同需求,可提供实心球和空心球。硬密封球阀球体球芯结构.jpg均采用实心球,表面经硬化喷涂处理,并和阀座密封面精密配磨而成 The spheres are precision machined by grinding machine, and the surface is polished by mirror, effectively ensuring the roundness of the spheres. According to the different needs of customers, we can provide solid balls and hollow balls. The hard seal ball valve balls are solid balls, the surface is hardened and sprayed, and they are precisely grinded with the sealing surface of the valve seat


主要零部件材料 Main parts and materials

氨用球阀球阀材质表.jpg

序号

名称

碳钢

不锈钢

1

阀体

A216 WCB

A351 CF8M

2

阀盖

A216 WCB

A351 CF8M

3

球体

A182 F304

A182 F316

3a

球体

A182F304+SFNi

A182F304+SFNi

4

阀杆

A182 F304

A182 F316

5

阀座

PTFE

PTFE

5a

阀座

A182F304+STL

A182F304+STL

5b

密封圈

柔性石墨

柔性石墨

6

填料压盖

A216 WCB

A351 CF8M

7

组合填料

PTFE

PTFE

8

手柄

A216 WCB

A216 WCB

9

中道垫片

PTFE

PTFE

9a

中道垫片

A182 F321+石墨

A182 F321+石墨

10

倒密封垫

PTFE

PTFE

10a

倒密封垫

柔性石墨

柔性石墨

11

六角螺栓

A193 B7

A193 B8

11a

内六角螺钉

A193 B7

A193 B8

12

六角螺栓

A193 B7

A193 B8

12a

双头螺栓

A193 B7

A193 B8

12b

六角螺母

A1942H

A1948


产品中心
相关产品